Sales & Support: 1.800.377.6329

Print This Page

DMC-18x0

PCI Optima Motion Controllers, 1-8 axes

DMC-18x0_image

Product Description

**For new applications, Galil recommends the new generation, Accelera series DMC-18x6.**

The DMC-18x0 PCI motion controller is a member of the Optima Series, Galil's prior-generation, multi-axis motion controllers. The DMC-18x0 controller accommodates 1- through 8-axis formats and allows control of step or servo motors on any combination of axes. Any mode of motion can be programmed including linear and circular interpolation, contouring, electronic gearing and ecam. Like all Galil controllers, programming the DMC-18x0 is simplified with two-letter, intuitive commands and a full set of software tools such as WSDK for servo tuning and analysis.

Questions?

Call 1.800.377.6329 to speak with a Galil Application Engineer.

Product Features

  • PCI card in 1 through 8 axis versions: DMC-18x0 where x=1,2,3,4,5,6,7,8 axes
  • Accepts up to 12 MHz encoder frequencies for servos and outputs pulses up to 3 MHz for steppers
  • PID compensation with velocity and acceleration feedforward, integration limits, notch filter and low-pass filter.
  • Modes of motion include jogging, point-to-point positioning, contouring, linear and circular interpolation, electronic gearing and ECAM
  • Multitasking for concurrent execution of up to eight application programs
  • Non-volatile memory for application programs, variables and arrays
  • Dual encoders, home input and forward and reverse limits accepted for every axis
  • 8 Uncommitted inputs and 8 outputs for 1- through 4-axes models, 16 inputs and 16 outputs for 5- through 8-axis models
  • Expansion for 64 I/O with optional DB-14064
  • 8 uncomitted analog inputs
  • High speed position latch and output compare
  • 2nd FIFO for instant access to status and parameters
  • High-density shielded cables and optical isolation for noise immunity.
  • Connects directly to AMP-19540 4-axis drive for cost-effective, multi-axis controller/drive solution. Drives brush or brushless servos up to 500 Watts each. Or, connect to external drives of any power range using ICM-2900 interconnect module
  • Communication drivers for Windows, QNX, and Linux
  • Custom hardware and firmware options available
  • RoHS CompliantCE Certified
Part Number Description 1pc/100pc
DMC-1810 PCI 1-axis Optima $1095 / $795
DMC-1820 PCI 2-axis Optima $1495 / $875
DMC-1830 PCI 3-axis Optima $1895 / $935
DMC-1840 PCI 4-axis Optima $2195 / $995
DMC-1850 PCI 5-axis Optima $2595 / $1345
DMC-1860 PCI 6-axis Optima $2795 / $1425
DMC-1870 PCI 7-axis Optima $2995 / $1525
DMC-1880 PCI 8-axis Optima $3195 / $1595
CABLE-100-1m 100-pin cable; 1 meter $175 / $135
CABLE-100-2m 100-pin cable; 2 meter $190 / $145
CABLE-100-4m 100-pin cable; 4 meter $210 / $160
CABLE-36-1m auxiliary encoder cable;1 meter $90 / $75
CABLE-36-3m auxiliary encoder cable;3 meter $110 / $90
CABLE-80-1m extended I/O cable; 1 meter $135 / $102
CABLE-80-4m extended I/O cable; 4 meter $160 / $112
ICM-1900 interconnect for 4 axis $345 / $245
ICM-1900-OPTO ICM with isolated ouputs $395 / $295
ICM-2900-FL ICM with flange mount $295 / $195
ICM-2900-OPTO-FL ICM with opto & flange $345 / $245
ICM-2900 interconnect for DMC-2xx0 $295 / $195
ICM-2900-OPTO ICM with opto outputs $345 / $245
ICM-2908 ICM for auxiliary encoders $125 / $95
CB-50-100 50-pin to 100-pin (for 5 thru 8 axes) $75 / $50
CB-20-25 20-pin to 25-pin (aux enc) $15 / $15
CB-36-25 36-pin to 25 pin (aux enc) $50 / $45
CABLE-26-25 26-pin to 25 pin (aux enc) $15 / $15
CB-50-80 50-pin to 80-pin (for DB-14064) $75 / $50
DB-14064 64 I/O expansion board $295 / $195
-16 bit ADC for analog inputs 16-bit analog-to-digital $100 / $60
AMP-19520 ICM with two 500W servo drives $595 / $395
AMP-19540 ICM with four 500W servo drives $795 / $495
-SR for AMP-195x0 Shunt regulator option for AMP $50 / $25
GalilSuite Servo Tuning and Analysis with Program Editor and Terminal $195
GalilSuite-Lite GalilSuite software without Scope and Tuner $0
Note: Pricing shown is for domestic purchases only.